The E3 error (also displayed as F5 E3) on your Whirlpool Washer means there is a lid lock failure preventing the washer from operating. This error indicates the lid cannot lock properly, which is a safety feature that prevents the washer from spinning when the lid is open.
| Error code | E3 (F5 E3) |
|---|---|
| Meaning | Lid lock failure or lid not detected as closed |
| Severity | Medium — Washer will not operate, but no immediate damage risk |
| Time to fix | 15–45 minutes |
| Tools needed | Flathead screwdriver, Phillips screwdriver, multimeter (optional) |
What the E3 error means
The F5 E3 error code on Whirlpool top-load washers indicates that the control board is not receiving the proper signal from the lid lock mechanism. The lid lock is a safety feature that prevents the washer drum from spinning while the lid is open, protecting users from injury. When the control board cannot verify that the lid is securely closed and locked, it displays this error and halts the wash cycle. This error typically appears when you try to start a cycle or during the wash when the washer attempts to transition to the spin cycle.
Common causes
- Faulty lid lock mechanism that has worn out or failed mechanically
- Misaligned lid strike or lid not closing completely
- Damaged or loose wiring connections between the lid lock and control board
- Failed lid lock switch that cannot send proper signals to the control board
- Debris or detergent buildup preventing the lid lock from engaging properly
- Control board malfunction preventing proper communication with the lid lock system
How to fix the E3 error
- Check the lid alignment and closure: Open and close the lid firmly several times to ensure it’s seating properly. Inspect the lid strike (the part on the lid that engages with the lock) to ensure it’s not loose, damaged, or misaligned. Tighten any loose screws on the lid or strike. Clean around the lid lock area to remove any detergent residue or debris that might prevent proper engagement. Try running a cycle to see if the error clears.
- Reset the washer: Unplug the washer from the electrical outlet or turn off the circuit breaker for 5 minutes. This allows the control board to reset and may clear temporary glitches. Plug the washer back in and try running a cycle. If the error persists, proceed to inspect the lid lock mechanism.
- Inspect and test the lid lock assembly: Unplug the washer for safety. Remove the screws securing the top panel or control console to access the lid lock mechanism (typically located under the top panel near the lid). Visually inspect the lid lock for any obvious damage, cracks, or broken parts. Check that all wire connectors are firmly attached. If you have a multimeter, test the lid lock switch for continuity according to your model’s specifications (typically should show continuity when engaged). If the lid lock is damaged or fails the continuity test, it needs replacement.
- Replace the lid lock assembly: If the lid lock is faulty, order a replacement part specific to your Whirlpool washer model (typically costs $50–$120). Disconnect the wire harness from the old lid lock. Remove the mounting screws and take out the defective lid lock. Install the new lid lock, secure with screws, and reconnect the wire harness. Reassemble the washer, restore power, and test with a wash cycle.
- Check wiring connections: With the washer unplugged, trace the wires from the lid lock to the control board, looking for any damaged, pinched, or corroded wires. Check all connector plugs to ensure they’re fully seated and not corroded. Repair or replace any damaged wiring using appropriate electrical connectors. Ensure wires are properly routed and not pinched when reassembling.
- Test or replace the control board: If all other components check out, the main control board may be failing to properly communicate with the lid lock. This is less common but can occur. Control board replacement is more complex and expensive ($150–$300), so verify all other causes first. Consider contacting a professional technician for control board diagnosis and replacement, as it requires technical expertise.
FAQ
Can I bypass the lid lock to use my Whirlpool washer with the F5 E3 error?
No, you should not bypass the lid lock safety feature. The lid lock prevents the washer from spinning with the lid open, which could cause serious injury. Bypassing this safety mechanism creates a dangerous situation and voids your warranty. Always repair or replace the faulty lid lock assembly properly.
How much does it cost to fix the F5 E3 error on a Whirlpool washer?
If you replace the lid lock assembly yourself, the part typically costs $50–$120 depending on your model. Professional repair service ranges from $150–$300 including parts and labor. If the control board needs replacement, costs can reach $250–$400 for DIY or $400–$600 with professional installation.
Why does my Whirlpool washer show F5 E3 even when the lid is closed?
The F5 E3 error appears when the lid is closed because the control board isn’t receiving the signal that the lid is locked, not just closed. This usually indicates a faulty lid lock mechanism, misaligned lid strike, or wiring issue rather than the lid actually being open. The lock mechanism must physically engage and send an electrical signal to the control board to confirm it’s secure.
META_DESC: Fix the Whirlpool washer F5 E3 error code with our complete guide. Learn what causes this lid lock failure error and get step-by-step repair instructions.