The TE error on your Samsung Dryer means there is a temperature sensor malfunction. The dryer has detected an issue with the thermistor, which monitors internal temperature to prevent overheating and ensure proper drying cycles.

Error code TE
Meaning Temperature sensor error or thermistor failure
Severity Medium — Dryer will not operate until resolved, but no immediate safety risk
Time to fix 30–60 minutes
Tools needed Multimeter, Phillips screwdriver, nut driver set, work gloves

What the TE error means

The TE error code indicates a problem with your Samsung dryer’s thermistor or its wiring. The thermistor is a temperature-sensing resistor that monitors the air temperature inside the drum and sends signals to the control board to regulate heating cycles. When the control board detects an abnormal resistance reading—typically an open circuit, short circuit, or reading outside the expected range—it triggers the TE error and shuts down the dryer to prevent damage or unsafe operation.

Common causes

  • Faulty or failed thermistor that provides inaccurate temperature readings
  • Damaged, disconnected, or corroded wiring connections to the thermistor
  • Blown thermal fuse caused by restricted airflow or overheating
  • Defective control board unable to properly read thermistor signals
  • Moisture or lint buildup affecting thermistor performance
  • Physical damage to the sensor from impact or excessive heat exposure

How to fix the TE error

  1. Unplug the dryer and access the thermistor: Disconnect power to the dryer for safety. Remove the lower front access panel or rear panel (depending on your Samsung model) using a Phillips screwdriver. Locate the thermistor, which is typically mounted on the heating element housing or duct assembly and connected by two wires.
  2. Test the thermistor with a multimeter: Disconnect the wire harness from the thermistor. Set your multimeter to measure resistance (ohms). Touch the probes to the thermistor terminals. At room temperature (approximately 70°F), a functioning thermistor should read between 10,000–12,000 ohms. An infinite reading indicates an open circuit (failed thermistor), while a zero reading indicates a short circuit.
  3. Inspect wiring and connections: Examine all wires leading to the thermistor for signs of damage, burns, fraying, or loose connections. Check wire harness connectors for corrosion or poor contact. Reconnect any loose wires and clean corroded terminals with electrical contact cleaner. Ensure all connections are secure and properly seated.
  4. Check the thermal fuse: Locate the thermal fuse on the heating element housing or blower housing. Using your multimeter set to continuity mode, test the fuse. A working thermal fuse should show continuity (zero resistance). If the fuse has blown (no continuity), it must be replaced. Address the root cause—usually restricted airflow from clogged vents—before replacing.
  5. Replace the thermistor if faulty: If testing confirms the thermistor is defective, order the correct replacement part for your specific Samsung dryer model. Remove the mounting screw holding the old thermistor, disconnect it completely, and install the new thermistor in the same position. Reconnect the wire harness securely.
  6. Reassemble and test the dryer: Replace all access panels and secure with screws. Plug the dryer back in and run a test cycle to verify the TE error has cleared. Monitor the first complete cycle to ensure proper heating and temperature regulation without error codes appearing.

FAQ

Can I reset the TE error without fixing the underlying problem?
No, simply resetting the dryer by unplugging it for a few minutes will not resolve the TE error. While this may temporarily clear the code from the display, the error will return as soon as the dryer attempts to heat because the control board will detect the same thermistor malfunction. You must diagnose and repair the faulty component.

How much does a Samsung dryer thermistor replacement cost?
A replacement thermistor for Samsung dryers typically costs between $15–$40 for the part itself. If you hire a professional appliance repair technician, expect to pay $150–$250 including labor and the service call fee. DIY replacement can save you $100–$200 if you’re comfortable working with electrical components and have basic tools.

Will my dryer work at all with the TE error code displayed?
No, your Samsung dryer will not operate when the TE error is active. The control board disables the dryer as a safety precaution because it cannot accurately monitor internal temperatures without a functioning thermistor. The dryer may tumble briefly but will not heat and will quickly display the error and stop the cycle.