The F138 error on your Miele Washing machine indicates a malfunction with the circulation pump or its power supply. This typically means the pump isn’t receiving proper voltage or has failed mechanically, preventing water from circulating during the wash cycle.
| Error code | F138 |
|---|---|
| Meaning | Circulation pump voltage fault or pump failure |
| Severity | High — Machine will not complete wash cycles |
| Time to fix | 30–90 minutes |
| Tools needed | Multimeter, screwdriver set, Torx drivers, pliers |
What the F138 error means
The F138 error code signals that your Miele washing machine has detected an issue with the circulation pump’s electrical supply or the pump itself has malfunctioned. The circulation pump is responsible for moving water through the drum during wash and rinse cycles, ensuring proper cleaning and distribution of detergent. When the control board detects that the pump isn’t receiving the correct voltage (typically 230V AC) or the pump motor has failed, it triggers the F138 code to prevent potential damage and alert you to the problem.
Common causes
- Faulty circulation pump motor with burned-out windings or seized bearings
- Loose or corroded electrical connections to the circulation pump
- Defective relay on the main control board that supplies power to the pump
- Damaged wiring harness between the control module and circulation pump
- Foreign objects lodged in the pump impeller preventing rotation
- Failed pump capacitor (on models equipped with capacitor-start pumps)
How to fix the F138 error
- Power cycle the machine and check for blockages: Unplug the washing machine for 5 minutes to reset the control board. Reconnect power and run a test cycle. If the error persists, turn off and unplug the machine. Access the circulation pump (usually located at the front lower section behind the kick plate) and check for debris blocking the impeller. Remove any obstructions and manually rotate the impeller to ensure it spins freely.
- Inspect electrical connections to the pump: With the machine unplugged, locate the circulation pump and examine all wire connections. Check for loose connectors, burnt terminals, or corrosion. Remove connectors, clean any corrosion with electrical contact cleaner, and firmly reattach. Inspect the wiring harness for damage, pinching, or signs of overheating.
- Test the circulation pump with a multimeter: Disconnect the pump’s electrical connectors and use a multimeter set to ohms to test resistance across the pump motor terminals. A functional pump typically shows 100–300 ohms (check your model’s specifications). An infinite reading indicates an open circuit (failed motor), while zero ohms suggests a short circuit. If readings are abnormal, the pump needs replacement.
- Check voltage supply to the pump: With extreme caution and proper safety precautions, reconnect the machine to power and activate a wash cycle while measuring voltage at the pump connector using a multimeter set to AC voltage. You should see approximately 230V AC when the pump should be running. If no voltage is present, the issue lies with the control board or relay.
- Inspect the main control board: If the pump tests good but receives no power, examine the control board for burned relays, damaged solder joints, or visible signs of failure. The relay that controls the circulation pump may have failed. If you have electronics experience, you can test the relay; otherwise, the control board may require professional replacement.
- Replace the circulation pump: If testing confirms pump failure, order a genuine Miele replacement pump for your specific model number. Drain any remaining water, disconnect hoses and electrical connections, remove mounting screws, and install the new pump. Ensure all connections are secure, seals are properly positioned, and hoses are firmly attached before testing.
FAQ
Can I run my Miele washing machine with the F138 error?
No, you should not attempt to run the machine with an F138 error. The circulation pump is essential for proper washing function, and running the machine could damage other components or flood your laundry area if water cannot circulate properly.
How much does a Miele circulation pump replacement cost?
A genuine Miele circulation pump typically costs between $150–$300 depending on your model. Professional installation adds $150–$250 in labor costs. Total repair costs generally range from $300–$550, though DIY replacement can save the labor expense.
Is the F138 error the same as F53 or other pump errors?
No, F138 specifically indicates a circulation pump voltage or electrical fault, while F53 relates to drain pump issues. Other codes like F11 or F51 address different drainage problems. Each code points to distinct components, so proper diagnosis using the specific error code is essential for correct repairs.