The F10 error on your Miele Washing means there’s a problem with the heating system or temperature sensor. This code typically indicates that the water isn’t heating properly or the machine can’t accurately detect water temperature.

Error code F10
Meaning Heating system fault or NTC temperature sensor failure
Severity Medium — Machine may run cold cycles only; requires repair to restore full function
Time to fix 15–60 minutes
Tools needed Multimeter, screwdriver set, pliers, work gloves

What the F10 error means

The F10 error code indicates your Miele washing machine has detected a malfunction in the water heating circuit or the NTC (Negative Temperature Coefficient) temperature sensor. The NTC sensor monitors water temperature and communicates with the control board to regulate the heating element. When the sensor fails, sends incorrect readings, or the heating element doesn’t respond properly, the machine triggers this error to prevent damage and alert you to the problem. Without proper heating function, your machine may only run cold water cycles or stop mid-cycle.

Common causes

  • Faulty NTC temperature sensor providing incorrect readings to the control board
  • Defective heating element that’s burned out or has broken connections
  • Damaged wiring or loose connections between the temperature sensor, heating element, and control board
  • Failed relay on the main control board that controls power to the heating element
  • Corroded or oxidized electrical connectors affecting signal transmission
  • Heating element covered with limescale buildup preventing proper heat transfer

How to fix the F10 error

  1. Reset the machine and run a diagnostic: Unplug your Miele washing machine for 5 minutes to reset the control board. Plug it back in and run a short hot water cycle to see if the error clears. If the F10 returns, proceed with further troubleshooting.
  2. Check the NTC temperature sensor: Disconnect power and access the heating element assembly at the bottom front of the drum. Locate the NTC sensor (small probe attached to the heating element). Disconnect it and test with a multimeter—resistance should be approximately 50,000 ohms at 77°F (25°C). Replace the sensor if readings are inconsistent or infinite.
  3. Inspect the heating element: With the machine unplugged, disconnect the heating element wiring. Use a multimeter to test resistance across the element terminals—you should see 20–30 ohms. Also test from each terminal to ground (metal drum)—this should show infinite resistance. If readings differ significantly, replace the heating element.
  4. Examine all wiring and connections: Carefully inspect wires leading to the heating element, NTC sensor, and control board for damage, burn marks, or loose connections. Check all connectors for corrosion or moisture. Clean corroded connectors with electrical contact cleaner and ensure all connections are secure.
  5. Test the control board relay: If the sensor and heating element test normal, the issue may be with the control board’s heating relay. Listen for a clicking sound when the machine should activate heating. If no click occurs or other tests indicate board failure, the control module may need professional replacement.
  6. Descale the heating system: If your area has hard water, run a descaling cycle using Miele descaling tablets or citric acid solution. Heavy limescale can insulate the heating element and cause sensor misreadings. After descaling, run a test cycle to verify the error clears.

FAQ

Can I still use my Miele washing machine with the F10 error code?
You may be able to run cold water cycles, but hot and warm water programs won’t function properly. Continuing to use the machine without fixing the F10 error means clothes won’t be cleaned effectively on cycles requiring heated water, and you risk potential damage to other components if the underlying issue worsens.

How much does it cost to repair a Miele F10 error?
The NTC temperature sensor costs $30–$60, while a heating element ranges from $80–$150. Professional repair typically costs $200–$400 including parts and labor. DIY repair can save significantly if you’re comfortable working with electrical components, though always disconnect power before servicing.

Why does my Miele washer show F10 only on certain cycles?
The F10 error appears during cycles that require heated water because that’s when the heating system activates. If the error only occurs on high-temperature cycles (above 140°F), the heating element may be partially functional but failing under higher demand, or the NTC sensor may be inaccurate only at elevated temperatures.