The E08 error on your Beko Dryer means there’s a problem with the dryer’s heating system, specifically a heating element or thermistor malfunction. This error prevents your dryer from heating properly and requires immediate attention to restore normal operation.

Error code E08
Meaning Heating element or thermistor failure detected
Severity Medium — Dryer will not heat but tumbler may still operate
Time to fix 30–90 minutes
Tools needed Multimeter, screwdriver set, work gloves, flashlight

What the E08 error means

The E08 error code indicates that your Beko dryer has detected a fault in the heating circuit, typically involving the heating element or the thermistor (temperature sensor). The thermistor monitors the dryer’s internal temperature and sends signals to the control board. When the control board detects abnormal resistance readings from the thermistor or heating element, it triggers the E08 error to prevent potential damage or unsafe operation. Your dryer may still tumble clothes but will not produce heat, leaving your laundry damp.

Common causes

  • Faulty or damaged thermistor with incorrect resistance readings
  • Defective heating element with broken coils or internal short circuit
  • Loose or corroded wiring connections to the heating element or thermistor
  • Failed thermal fuse or high-limit thermostat interrupting the heating circuit
  • Control board malfunction causing false error detection
  • Excessive lint buildup around heating components affecting sensor readings

How to fix the E08 error

  1. Unplug the dryer and check for basic issues: Disconnect power to your Beko dryer for safety. Remove the lint filter and clean it thoroughly, then check the exhaust vent for blockages. Clear any lint buildup around the drum and internal components. Wait 5 minutes, then plug the dryer back in and test if the error clears. This resolves the issue in about 10% of cases.
  2. Access and inspect the thermistor: Unplug the dryer and remove the rear or top panel (depending on your model) to access the heating assembly. Locate the thermistor, which is typically mounted near the heating element or on the air duct. Check for visible damage, corrosion, or loose wire connections. Test the thermistor with a multimeter set to ohms—it should read approximately 50,000 ohms at room temperature (68°F). Replace the thermistor if readings are significantly different or if it shows infinite resistance.
  3. Test the heating element: With the dryer unplugged and panels removed, locate the heating element assembly. Disconnect the wires and use a multimeter to test for continuity. A functional heating element should show 10–50 ohms of resistance (check your model’s specifications). Also test from each terminal to the metal housing—there should be no continuity, indicating no short to ground. Replace the heating element if it’s broken, shorted, or shows incorrect resistance values.
  4. Inspect thermal safety devices: Check the thermal fuse and high-limit thermostat located on or near the heating element housing. Test each with a multimeter for continuity. These safety devices should show zero resistance when functional. Replace any thermal fuse or thermostat that shows no continuity, and investigate what caused them to fail (usually restricted airflow).
  5. Examine all wiring connections: Carefully inspect all wire harnesses connected to the heating element, thermistor, and control board. Look for burned, frayed, or corroded wires. Check connector terminals for tightness and corrosion. Clean corroded connections with electrical contact cleaner and reconnect securely. Replace any damaged wiring harnesses.
  6. Reset or replace the control board if necessary: If all heating components test good, the control board may be faulty. Try performing a hard reset by unplugging the dryer for 10 minutes. If the E08 error persists after replacing all heating components, the control board likely needs replacement. This repair typically costs $150–$300 for parts and professional installation.

FAQ

Can I still use my Beko dryer with the E08 error code?
No, you should not continue using your dryer with the E08 error. While the drum may tumble, the dryer won’t heat properly, which means your clothes won’t dry. Continuing to run cycles wastes electricity and could potentially cause further damage to electrical components if there’s an underlying short circuit or wiring issue.

How much does it cost to fix a Beko dryer E08 error?
The repair cost depends on which component has failed. A thermistor replacement typically costs $30–$60 for the part plus $100–$150 for labor if professionally installed. A heating element costs $50–$120 for the part plus similar labor charges. If the control board needs replacement, expect $150–$300 total. DIY repairs can save the labor costs but require proper tools and electrical safety knowledge.

Is the E08 error covered under my Beko dryer warranty?
Coverage depends on your specific warranty terms and the age of your dryer. Most Beko dryers come with a 1-year parts and labor warranty, with some components covered for up to 10 years. If your dryer is within the warranty period and the failure wasn’t caused by misuse or lack of maintenance, the repair should be covered. Contact Beko customer service at 1-866-239-8450 or check your warranty documentation to verify coverage before paying for repairs.