The TE2 error on your LG Dryer means there’s a problem with the thermistor (temperature sensor). This sensor monitors the internal dryer temperature, and when it fails or provides incorrect readings, the dryer stops to prevent overheating or improper drying.
| Error code | TE2 |
|---|---|
| Meaning | Thermistor (temperature sensor) failure or malfunction |
| Severity | Medium — Dryer will not operate until fixed |
| Time to fix | 30–60 minutes |
| Tools needed | Multimeter, screwdriver set, nut driver, flashlight |
What the TE2 error means
The TE2 error code indicates that the thermistor in your LG dryer has failed or is sending incorrect temperature readings to the control board. The thermistor is a small temperature sensor that monitors the air temperature inside the dryer drum and provides feedback to the control board to regulate heating cycles. When this sensor malfunctions, provides readings outside the normal range, or becomes disconnected, the dryer’s safety system triggers the TE2 error and stops operation to prevent potential damage or safety hazards.
Common causes
- Faulty or damaged thermistor that has failed electronically
- Loose or disconnected wiring harness to the thermistor
- Corroded or damaged wire connectors at the thermistor connection point
- Thermistor dislodged from its mounting position on the blower housing
- Control board issue preventing proper thermistor signal reading
- Moisture or debris buildup affecting thermistor performance
How to fix the TE2 error
- Unplug the dryer and access the thermistor. Disconnect power to the dryer for safety. Remove the front or rear panel depending on your model (most LG dryers require rear panel removal). Locate the thermistor, which is typically attached to the blower housing near the heating element assembly. It’s a small sensor with two wires connected.
- Inspect the thermistor and wiring connections. Check for any visible damage, burn marks, or corrosion on the thermistor and its wire connectors. Ensure the wiring harness is firmly connected. Disconnect and reconnect the wire connector to ensure a solid connection. Clean any debris or lint that may have accumulated around the sensor.
- Test the thermistor with a multimeter. Set your multimeter to measure resistance (ohms). Disconnect the wire connector from the thermistor and test across the two terminals. At room temperature (around 70°F), the thermistor should read approximately 10,000-12,000 ohms. If the reading is infinite (open circuit) or zero (short circuit), the thermistor has failed and needs replacement.
- Replace the faulty thermistor. If testing confirms the thermistor is defective, order a replacement part specific to your LG dryer model. Remove the mounting screw or clip holding the old thermistor, disconnect the wires, and install the new thermistor in the same location. Reconnect the wiring harness securely and ensure the sensor is properly positioned against the blower housing.
- Reassemble and test the dryer. Replace the access panel and secure all screws. Plug the dryer back in and run a test cycle to verify the TE2 error has cleared. The dryer should heat normally and complete the cycle without error codes. If the error persists after thermistor replacement, the control board may need professional diagnosis.
FAQ
Can I bypass the thermistor to run my dryer temporarily?
No, you should never bypass the thermistor. This sensor is a critical safety component that prevents overheating and potential fire hazards. Operating the dryer without a functioning thermistor can damage the heating element, melt internal components, or create dangerous conditions.
How much does it cost to replace an LG dryer thermistor?
The thermistor part typically costs between $15 and $35 depending on your specific model. If you hire a professional appliance repair technician, expect to pay $150–$250 total including parts and labor. This is a relatively straightforward DIY repair that can save you labor costs.
What’s the difference between TE1 and TE2 error codes?
The TE1 error typically indicates a thermistor reading that’s too high (short circuit), while TE2 indicates a thermistor reading that’s too low or open circuit. Both codes point to thermistor issues, but TE2 more commonly indicates a complete sensor failure or disconnection rather than a reading out of range.